Features & Benefits

P5100A

• DC to 500 MHz
• 2500 V_Peak, 1000 V_RMS CAT II
• 100X with Readout Coding
• UL3111-1, EN61010-1, IEC61010-2-031, CSA1010.1, CSA1010.2.031
• 7 to 30 pF Compensation Range

TPP0850

• DC to 800 MHz
• 2500 V_Peak, 1000 V_RMS CAT II
• 50X with Readout Coding
• Designed for use with the MSO/DPO5000 and MSO/DPO4000B Series Oscilloscopes

P5122

• For TPS2000 and THS3000 Series Oscilloscopes
• DC to 200 MHz
• 1000 V_RMS CAT II when DC-coupled*¹
• Floatable up to 600 V_RMS CAT II
• 100X
• IEC61010-031

P5150

• For TPS2000 and THS3000 Series Oscilloscopes
• DC to 500 MHz
• 2500 V_Peak, 1000 V_RMS CAT II
• Floatable up to 600 V_RMS CAT II or 300 V_RMS CAT III
• Preferred Probe for Ripple Measurements
• 50X
• 10 to 25 pF Compensation Range
• UL61010B-2-031, EN61010-2-031, IEC61010-2-031, CSA61010.2.031

P6015A

• High Voltage – 20 kV DC / 40 kV Peak (100 ms Pulse Width)
• High Bandwidth – DC to 75 MHz
• Silicone Dielectric
• Optional 1000X Readout Coding
• Wide Compensation Range (7 to 49 pF)
• Heavy-duty Versatile Ground Lead and Alligator Clip

Applications

• Power Supply Design
• Design Motor Drive
• Electronic Ballast
• Power Semiconductors
• Switch Mode Control
• UPS Systems
• Power Converters

*¹ The P5122 probe should not be used on the TPS2000 Series oscilloscopes for AC-coupled measurements on signals with greater than 300 V DC offset. The P5150 is the recommended probe for measuring ripple on high-voltage DC supplies.

P5100A High-voltage Probe

The P5100A is a low input capacitance high-voltage probe (2.5 kV) designed for higher-frequency applications. The probe can be compensated to match plug-ins and oscilloscopes with nominal input capacitances of 7-30 pF. A variety of screw-on accessories provide easy connection to the device-under-test.

TPP0850 High-voltage Probe

The TPP0850 offers the industry’s highest bandwidth probe (800 MHz) for high-voltage signals (up to 2500 V_p-p). This is ideal for testing power semiconductors and switch-mode power supplies, which continue to increase in switching speed to minimize power loss, creating a need for faster rise time, higher bandwidth, and higher voltage probes. The TPP0850 meets this need and can be used with switching transistor circuits operating at 1200 V_RMS, above the voltage operating range of standard general-purpose probes. It will also be able to accommodate emerging power applications that will require even faster rise time capabilities.

P5150 and P5122 IsolatedChannel™ Applications

In many applications, it is important to be able to isolate the measurement from earth ground and also to isolate the common voltage between channels. The P5150 or P5122, coupled with the TPS2000 and THS3000 Series digital storage oscilloscopes, deliver both the isolation for the measurement from earth ground and full isolation between the channels. The P5150 is the recommended probe for measuring ripple on high-voltage DC supplies. The P5122 probe should not be used on the TPS2000 Series oscilloscopes for AC-coupled measurements on signals with greater than 300 V DC offset.

P6015A High-voltage Probe

For heavy-duty high-performance measurements of voltages over 2.5 kV, the P6015A is the industry standard. You can measure DC voltages up to 20 kV_RMS and pulses up to 40 kV (peak, 100 ms duration). The 75 MHz bandwidth enables you to capture fast, high-voltage signals.

The P6015A uses an environmentally safe silicone compound for a dielectric and never needs refilling. Other features include: A 7-49 pF compensation range, small compensation box that fits on adjacent amplifier inputs, and a readout option for use with most Tektronix digital scopes. With the readout option, displayed voltage amplitude values will be the actual signal value rather than understated by a factor of 1,000.

Note: Using the readout version with other than Tektronix digital scopes may result in an erroneous readout display.